TABLE I. Dash numbers and characteristics. 1/
At +25°C
Dash numbers 2/
Over temperature range
Speci-
Coil
Lead
Lead
Lead
Spreader
Speci
Speci-
Speci-
Speci-
Speci-
Speci-
Speci-
Coil circuit
Supply
fied
resis-
length
length
length
pad
fied
fied
fied
fied
fied
fied
fied
current (mA)
voltage
pick-
tance
1.500
.187
.500
(fig. 2)
6/ 7/
hold
drop-
base
pickup
hold
drop-
base
(V dc)
up
(ref.
min
+.050
min
4/
volt.
out
current
volt.
volt.
out
current
5/
volt.
only)
3/
-.010
(V dc)
volt.
to
(V dc)
(V dc)
volt.
to
(V dc)
ohms
7/
(V dc)
assure
7/
7/
(V dc)
assure
7/
6/
7/
turnon
7/
turnon
Max
Min
Rated
Max
(mA)
(mA)
017
025
033
041
5.0
8.0
125
47.8
34.7
2.6
1.4
0.22
.28
3.6
2.0
0.15
1.20
018
026
034
042
6.0
11.0
255
27.7
21.2
3.5
2.0
0.28
.20
4.8
2.8
0.18
0.78
019
027
035
043
9.0
16.0
630
16.8
11.8
5.4
3.0
0.54
.13
7.8
4.2
0.35
0.48
020
028
036
044
12.0
22.0
1,025
13.6
10.1
6.6
4.0
0.63
.10
10.0
5.6
0.41
0.39
021
029
037
045
18.0
33.0
2,300
9.1
6.7
9.8
6.0
0.91
.07
14.5
8.4
0.58
0.26
022
030
038
046
26.5
45.0
4,000
7.7
5.7
12.8
8.0
1.37
.05
19.0
10.4
0.89
0.20
023
031
039
047
32.0
57.0
6,500
5.8
4.2
18.7
10.0
1.60
.04
24.0
15.0
1.00
0.16
024
032
040
048
40.0
75.0
11,000
4.3
3.1
23.3
13.0
2.10
.03
30.0
18.7
1.30
0.13
1/ Each relay possesses high level and low level capabilities. However, relays previously tested or used above 10 mA resistive at 6 V dc
maximum or peak ac open circuit are not recommended for subsequent use in low level applications.
2/ The suffix letter L, M, P, or R to designate the applicable failure rate level shall be added to the applicable listed dash number. Failure rate
level (percent per 10,000 cycles): L, 3.0; M, 1.0; P, 0.1; R, 0.01. Example: 017L - - - - - -032R.
3/ 1.500 leads are inactive for new design.
4/ Relays supplied with spreader pads (-041 through -048) shall have the pad rigidly attached.
5/ CAUTION: The use of any supply voltage less than the rated supply voltage will compromise the operation of the relay.
6/ When rated supply voltage is applied to the supply terminals, the coil circuit current must be within the limits shown. Measure at 25°C at
rated supply voltage for 5 seconds, maximum.
7/ Set base current from 3 mA to 15 mA during electrical measurements.